designed & dimensioned in millimeters[inches] do not scale from this print pesc-xx-xx-xx-01-x-ra-xx power positions (per end) -01, -02, -04 right angle signal positions -12, -40 plating specification -s: selective 30 au / 50 ni min on contact, matte tin on tail -t: matte tin, contact and tail -l: light selective, 10 au / 50 ni on contact, matte tin on tail option -sd: screw down (see fig. 1, sht 1) -lc: locking clip (use lc-11-tm) (see fig. 2, sht 2) -01, -02, -04 power positions (per end) * * * * - see table 1 for available combinations -01 lead style b 5.72 (typ) .225 0.50 (typ) ref .020 12.00 .472 ref 2.54 (typ) .100 22.86 .900 (9 spaces @ 2.54 [.100]) 2.54 (typ) .100 "d" (see table 2) 11.43 .450 (typ) ref "b" (see table 1, sheet2) 3 max sway (typ) "a" "a" "b" "b" pes-02-ra-sd-40 c1 c3 c4 c2 01 04 25.20 .992 ref "a" ref (see table 1, sheet 2) "c" (see table 1, sheet 2) 3.81 .150 (typ) ref 2.54 ref (typ) .100 0.38 ref (typ) .015 "f" "f" 1.42 ref .056 6.60 .260 (typ) ref 2.35 .093 0.64 (typ) ref .025 8.30 ref .327 4.44 - 0.13 + 0.20 .175 - .005 + .008 2.54 (typ) .100 section "a"-"a" sub-c-205-xx-x c6 2.04 .080 section "b"-"b" c7 2.54 .100 4.29 .169 2.68 (typ) ref .105 2.54 (typ) .100 section "f"-"f" c-08-02-x c-08-03-x c-08-05-x c-08-07-x c5 c fig. 1 pesc-01-40-01-x-ra-sd shown b sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: right angle power socket by: pesc-xx-xx-xx-01-x-ra-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b. cooper 11/24/2009 2 1 sheet scale: 1:0.666667 insulator: lcp, color: black terminal: copper alloy f:\dwg\misc\mktg\pesc-xx-xx-xx-01-x-ra-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: 2.22n [.5 lb]. 4. parts to be packaged in trays. 5. parts placed in tray with pin #1 facing the right side, due to pin numbering order. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision b
3 max sway (typ) 2.75 .108 3.50 .138 (measure at tip of pin) "c" (see table 1) 3 max sway (typ) pes-02-ra-lc-40 lc-11-tm c8 0.64 (typ) ref .025 8.86 .349 includes carrier in-process 1 c-08-02-x 4.29 .169 13.94 .549 includes carrier in-process 2 c-08-03-x 2.54 .100 19.75 .778 includes carrier in-process 3 c-08-05-x 2.54 .100 24.83 .978 includes carrier in-process 4 c-08-07-x b sheet of right angle power socket by: pesc-xx-xx-xx-01-x-ra-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b. cooper 11/24/2009 2 2 sheet scale: 1.5:1 revision b f:\dwg\misc\mktg\pesc-xx-xx-xx-01-x-ra-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
